Double Glazing Lock Repairs

Good locks on your windows and doors will help prevent burglars from entering your home. They usually don't want to break glass or try to get through windows that are open.

Some owners of double glazing, however, have had issues with their door or window lock after the installation. Fortunately, these issues are usually fixable and don't require to buy new double glazing.

Broken or faulty locks

If your uPVC window or door lock is damaged or broken or has a problem, a locksmith will repair it for you. They can repair hinges, striker plates and locks for your double-glazing. They will also be able to move the cylinder around to fix any misalignment issues that could be causing your handle to not work correctly.

The mechanism could be seized when the key fits into the lock, but it will not turn or be difficult for you to insert. The dirt or grease could be trapped in the mechanism. If this is the case, it may be possible for the lock to be cleaned and lubricated. It is essential to use a dry lubricant, like graphite or teflon instead of oil which can attract dirt and adhere to the inside of the mechanism. After the lubrication, insert the key into the lock and turn it. The lubricant must get into the mechanism, and the lock should turn effortlessly.

A damaged lock can be caused by loose screws in the lock mechanism. They can loosen and break off or fall out completely which can stop the lock from functioning properly. The screws can be tightened using the help of a screwdriver. However, be cautious not to tighten them too much. This could damage the internal components.

A damaged lock could be dangerous for both you and your family, especially if you have small children. They could easily open the door without your knowledge and gain access to your house. If you're worried about the possibility that this could occur, a licensed professional locksmith can help re-secure the double glazing doors.

Misty Glaze is a professional uPVC company in Lancing that can Repair My Windows And Doors all types faulty and broken mechanisms on both uPVC doors and windows. We can also reconfigure your uPVC or double glazing locking system to meet your particular requirements, which means that in most cases, replacement doors and windows are not required.

Handles that are damaged or faulty

As part of their overall security plan, many double-glazed windows have a multipoint lock. This is a great choice for Window Doctor those who are concerned about opportunistic thieves looking to gain entry to your home. Ask your locksmith about antilift blocks. They can be installed in addition to existing locks and will ensure that your windows are securely shut.

It's not uncommon for handles to be damaged or even fail - they are the first component of your window that could be pushed open by a criminal intent on breaking into. Fortunately, the good news is that this is among the easiest parts to repair.

Modern uPVC and aluminium handles have a multi-point locking mechanism known as Espagnolette that is designed to resist forced entry. This security upgrade is offered as an option for new uPVC windows. Older uPVC and aluminium handles can be upgraded to lock systems that shoot bolts and again as an additional option on double-glazed windows.

It is important to repair handles as quickly as possible if it is damaged. A damaged handle could prevent the window from closing properly and allow drafts to get in. It may also be a weak point that burglars with a plethora of opportunities could exploit, therefore putting your family and belongings at risk of being stolen.

The process of fixing the damaged mechanism begins with getting access to the window frame and removing the damaged handle. The gearbox is then opened to identify the type of gearbox used to open the handle. This will allow a replacement that matches the profile and the internal window frame mechanisms.

After the mechanism is replaced the handle can be put back together using the original screws. However, we suggest replacing them with larger screws to ensure a more secure fit. The final step is to apply a layer of clear sealant to shield the handle from further rust. Once that's done the window will be functional again and at a fraction of the cost of replacing the entire window.

Broken or Faulty Hinges

If your windows do not close correctly, draughts may get in, your home's security barriers will become weaker and there's an increased risk of damp or water damage. Broken or damaged window hinges are a typical problem that can be fixed easily.

If your uPVC windows don't open or shut it's likely that the hinges need to be replaced or repaired. While most window manufacturers require you to purchase a whole new window unit to solve this issue We can replace the faulty hinges and save you money.

Window hinges are often damaged after repeated use, or they might be damaged due to corrosion over time. If you find a broken hinge, it is important to take precautions to avoid further damage by taking care not to make the window swing open or closed.

You can locate the appropriate parts for your hinge by identifying the type of hinge it is. Maco, Mila and Roto are all window hinges. Get advice from a professional before purchasing parts that won't work with your existing hardware. This can cause more damage.

Faulty hinges are a major issue for uPVC windows and doors. They can be an important source of noise, and could also allow water to enter your windows.

Make sure whether the pin barrels on both hinge halves are aligned. If not then tap the headpin using the hammer to make a slight bend in hinge barrel. This will help keep the pin in the right position. A friend can help you hold the doors while you take off hinge screws and hinges. Replace the hinges and attach screws with glue. Finally put the hinges in place using weights or clamps while the glue is drying.

After you have fixed your hinges, you can install the door again. You can also attach the handle. Replace the screws with wooden dowels of the same size as the screw that was used to ensure they are in line.

Glass that is Broken or damaged

uPVC Windows can become damaged over time, despite the fact that they are excellent at keeping out the cold and conserving heat. This can be the case with damaged or broken glass and defective locks. If left unattended, this can become a very costly issue. It can also detract from the aesthetics of your home and may lead to a loss of insulation, so it's important to repair any damage as soon as you can.

If your glass has broken but isn't shattered it is usually possible to repair it yourself with the proper tools and techniques. Make sure the area surrounding the broken glass is clear of debris to ensure that fragments don't cause injury or trip hazards. Remove the broken glass pieces and dispose of them in the proper way. Then, apply masking tape to the entire area to keep shards from scattering and sticking to your skin when you move them. If you're dealing with a double-pane glass it's best to pre-fit the pane of glass before glueing it back in place to ensure that you'll have enough space to complete the task.

Before applying the glue, clean the surface of the damaged frame and the glass with a a dry, clean cloth. Follow the curing and application instructions that may differ from product-to-product. Based on the degree of the crack you may need to clamp the glass during curing. This can be done using lightweight clamps specifically designed to support fragile materials.

Once the adhesive is fully cured, carefully reinstall the glass into the window frame, making sure it's flush with the edges of the frame, Repair My Windows And Doors and there aren't any gaps between the glass and the window sash. Be cautious not to flex the window while it's put back in place, as this can weaken the seal and cause water infiltration and condensation.

If you have a glass door that's completely broken or has larger cracks, call a professional glazier such as O'Brien(r) to arrange an exchange. It's crucial to act fast when you notice broken glass.