Double Glazing Door Lock Repairs

Has your uPVC window doctor or door mechanism started to fail? Perhaps the door or window handles aren't able to connect properly or are hard to use.

You'll lose energy when your double-glazed doors do not work properly. This also increases the likelihood of burglaries. Owen the Locksmith will be able to repair your door lock for repair my windows and doors a reasonable cost.

Snapped Key

It can be frustrating when a key snaps inside the lock. It also poses a security risk since the door may not lock and make you vulnerable to burglars. Fortunately, there are quick fixes you can attempt to fix the issue and get your door functioning properly again.

Be sure to remain calm. If you panic you may end up pushing the broken key piece further into the lock.

Next spray WD-40 or another penetrating oil into the lock to help the broken piece to slide out more easily. You can also use a screwdriver to help break up any pieces stuck that might be blocking the way. If you happen to have a small piece of the key visible it, you can use a paperclip or some other metal object with a thin surface to grab it and then pull it out. Both of these methods work, but be very careful not to push the damaged piece of the key deeper into the keyway.

Some paperclips have grooved edges, which can serve as a hook extractor and some Jigsaw blades also work for this use. If you don't happen to have one of these tools, Repair My Windows And Doors you can bend a hook using needle-nosed pliers. Finally, a pair of tweezers can be used to grasp and remove the remaining piece of the key that was broken.

If you cannot remove the broken piece of key, use a lock deicer. It is found in most hardware stores. It works by freezing any moisture or ice that might be inside the lock.

If none of these solutions seem to work, it may be time to contact a locksmith. The experts at Fitlocks can quickly fix problems such as broken handles or snapped keys using uPVC locks and door mechanisms. They can also alter your double glazing door mechanisms to make them more user-friendly. Request a Repair My Windows And Doors for your double glazing through us online or give us a call to discuss your needs.

Broken Cylinder

A broken cylinder can be a serious security risk. A professional locksmith can easily fix the cylinder. A locksmith must tap the cylinder to fix it. They can do this using a hammer or other tool, but the most efficient way is to make use of a long match or a piece of wire. Then, position the match's tip or wire close to the keyway. The locksmith will hit the lock to break it open. This is better than using the hammer, which could damage the lock.

Overheating is the main reason behind cylinder heads cracking. This can happen when the block and cylinder head are made of different metals like cast-iron and aluminum. When various metals are heated and cool at different rates, it can create hotspots locally that expand faster than the rest of the cylinder head, thus leading to cracks.

Corrosion can be a reason for cylinder fractures. If the cylinder head and the block of the cylinder are not properly maintained, it can result in corrosion or rust that could cause them to expand at a higher rate than they ought to. In time, this could also cause cracks.

If your uPVC window or door lock is brittle and requires a lot more pressure to turn it could be due to a variety of causes. A defective locking mechanism, misalignment or an old handle are the most common causes of this issue.

Fortunately, this is an easy and cost-effective fix for the majority of homeowners with double glazing. A professional locksmith will usually be able solve the issue within an hour of arriving at your property. Based on your requirements they can change the locking mechanism, change the window handles, and also change the gearboxes. A locksmith with experience can always advise you on the most cost-effective options for your home. They may suggest upgrading to 3 Star TS007 Euro Cylinders, which provide an additional layer of protection from burglars. It is a small cost to pay for the peace-of-mind that comes from knowing your uPVC door is secure.

Broken Handle

Window handle locks have complex mechanisms that become less effective with age and usage, so it's no surprise they occasionally break. It isn't easy to determine the reason behind a broken window handle lock and repair it correctly.

Fixing the broken handle, regardless of whether it's the internal latch or locking mechanism can increase the security of your uPVC door and prevent draughts. It can be expensive to replace or repair the handle in a way that isn't done correctly. It can also harm the frame and lock of your door.

Screwdriver When the window is open and the screw loose, loosen the handle. The screw should be located on the inside of the backplate, usually concealed by an eye-catching cap to conceal it for aesthetic purposes. Be sure not to lose any of the internal components inside the handle, such as the levers or plates on the opposite side of the spindle. Ideally, keep them in the same place so you can replace them again when needed.

Then, with another screwdriver loosen the screw that holds the handle to the spindle at the back. Once the screw is loose, remove the handle and take out the broken spindle. Replace it with a brand new one, making sure that it's the same length as the old one (you can typically find these on the internet or in hardware stores) and securely screw it into the correct position. Do not overtighten the screw because this could cause damage to the handle and window frame.

Close the handle and try it. Hopefully, it will work smoothly and you'll be able open your window once more.

Don't forget to double-check that your uPVC window is closing properly when you're using the handle. If they're not closing properly, you could experience damp or draughts in your home. It could also affect the energy efficiency of your home. Core Sash Windows is a local window company that can alter the hinges of your window frames to ensure that they close correctly.

Broken Spindle

It is more likely for the spindle to break than the handle. This is most typical in uPVC tilt and turn windows. These windows require a handle that acts as a locking mechanism within the window frame. The handle is attached to a centre rod that is then activated by a series of mushroom-like locking cams, these locks are inserted into the window frame. If the dead latch mechanism does not open when the handle is turned, it is possible that the spindle has been damaged and this could be a very frustrating issue.

Fortunately there are steps that can be taken to fix this problem. A good locksmith will be able to quickly and efficiently repair this problem. A professional locksmith will be able to disassemble the window's handle using a tool that removes the wheel portion that houses the spindle. This can be done without damage to the handle or window frame.

After removing the wheel, the technician can inspect the spindle and determine the cause of the break. This involves disassembling the spindle, and then examining each component, noting any damage or excessive wear. The process is done in a clean, well-lit room by skilled technicians.

Then, clean the damaged spindle. This will remove any dirt or debris which may be obstructing it from functioning normally. Following this the spindle is cleaned, it can be repaired or replaced. If the technician is replacing the spindle he can use a dowel that is the same size to the original. He will then drill holes that are identical to both pieces. This will ensure that the new spindle is an exact fit with the handle.

If the damaged spindle can't be repaired, it might need to be replaced entirely. Home centers sell generic replacements, but if your window style is rare, you will need to contact an expert in cabinet making or woodworking who can recreate the exact piece. Once the new spindle is in place it can be positioned to the handle by line up the screw holes in the handle with the frame's existing screws. Once the new handle is firmly installed, you are now ready to operate your uPVC window.