How to Replace a Hyundai I10 Key Fob Battery

The Hyundai i10 sports a chic interior that competes with the Volkswagen UP and Citroen C1, as well as SEAT Ibiza. Its interior is more luxurious than rivals like the Citroen C1, Volkswagen UP and SEAT Ibiza.

Hyundai's key fob performs a lot of work for you, including locking and unlocking your car remotely. It also has a mechanical key that is able to be used in the event the battery in your fob goes out.

Dead Coin Battery

The key fob is an amazing invention that allows drivers to lock and start their vehicles without the need for a key in the ignition. This is accomplished by radio frequency signals which communicate with the onboard computer of the vehicle.

The battery inside the key fob is responsible for this signal and will eventually degrade and will require replacement. Depending on your Hyundai model, you might or may not get an alert that indicates the battery is about to go out of. Keep a spare keyfob handy for you to swap out the battery swiftly when it wears out.

The key fob has to be reprogrammed for the vehicle once the new battery has been installed. It is possible to do this using an OBDII or Hyundai Digital Key scanner, but it is usually easier to do it at your Reno home. Follow the directions in the owner's manual or look on YouTube for "how to replace and open the Hyundai keyfob battery." Make sure to take a photo of the old battery or write it down before removing it.

After the key fob has been reset, it should function again. If it doesn't work, you'll need to visit a dealership for a replacement or contact an online locksmith. They'll have the experience and tools to fix the issue.

Water Damage

Key fobs can be a very useful piece of technology. It lets you lock your vehicle from the comfort of home, open your windows from outside, and even start your car. It is not indestructible and will eventually wear out due to normal use. The replacement process for the Hyundai keyfob i10 battery is simple and cost-effective.

It's not unusual to drop your key fob into the water, a puddle, or even a washing machine. It can be rescued when you act quickly. A key fob that is wet is bad for electronics. It could cause corrosion, short-circuits, and even failure.

The first step is to remove as much water as possible. Flip the fob over and shake off any moisture that could be visible. You might also be able to place it on top of an electric radiator or a hairdryer to speed up the process. After removing as much moisture as you can, it's worth placing the fob in a place that is warm and dry where it will continue to dry out for some time.

Next, you should attempt to open up the fob to remove the battery that was in it. The majority of hyundai i10 remote key replacement key fobs that are i10 use the same battery that's found in many quartz watches and are generally very simple to replace. After you've replaced the battery, you should capture a picture or take note of the way it is positioned before closing up the fob.

Poor Battery Contact

The battery in your key fob could be worn out. This is a typical issue and typically the remote begins to show signs of trouble well before it gives up completely. Make sure the clips are not corroded or loose. If they are, clean them using a proper battery cleaning solution and a wire brush. Make sure you are using a button cell battery that has the same size, voltage and specifications as the original.

This could also indicate that your alternator isn't working properly. The alternator is the part that recharges your battery when you drive. A malfunctioning alternator can drain the battery quickly and cause the warning light to turn on.

A quick voltage check can aid in determining whether this is the case for your Hyundai. If the battery is in good condition, there's a possibility that the issue is with the circuit board or some other part of the key fob. You can open the key fob by pressing a small metal tab, or button on either the front or back of the device. After you take off the cover, you can insert the new CR2032 battery, making sure that all the connections are contacted.

Reprogramming

Hyundai offers keyless entry on a number of its models, making the trip around Littleton, Parker, and Castle Rock, CO easier than ever. If you own an ignition key you can open and lock your vehicle's doors and start the engine using the remote. But, it's not completely safe and a damaged key fob can cause problems. If your Hyundai key fob isn't working it could require reprogramming to work with your vehicle.

First, you have to remove the battery. Typically the button cell battery is located inside of the tab made of plastic. When you remove the tab, make sure you replace the battery with a battery with the same size and voltage as the old one.

Once the battery has been replaced, close the tab and replace the retaining clips. Then check the key fob to see whether it's still functioning.

If the key fob doesn't work, it could be time to talk to a dealer or locksmith. A dealer or locksmith can cut a new key and remote for you, and they can also program the key to work with your vehicle. They typically charge a fee to do this, but it's well worth the investment if you need your Hyundai key fob to continue working. They can also help you identify the most suitable Hyundai key fob for your needs.