Repairs to uPVC Windows

uPVC is an excellent option for modern homes. They are durable, long-lasting and easy to maintain. Unlike timber and aluminium, they are not susceptible to rust or rot.

Regularly cleaning and lubricating UPVC windows and doors is vital. This will save you from costly repairs and improve energy efficiency.

1. Broken Glass

If the glass in your window has been damaged, it can cause a huge amount of damage to your home, which can make it very hazardous and possibly fatal. It is important to make sure that your windows are in good condition.

Single-pane windows are relatively simple to replace and will usually fit into the frames that were previously in use very easily. However when windows with double panes are secured by internal beading, it'll be more difficult to get rid of the old panes and put in new ones. In this situation you'll need find some plastic spacers to help the new pane to fit correctly into the frame of the window.

Wearing eye protection and thick gloves is essential if you plan to remove the glass by yourself. It is also recommended to lay down a drop cloth prior upvc Window Repair to when you begin working on the glass, so that any fragments of glass fall onto the cloth instead of onto the floor, where they could be trampled on and cause further damage.

Once the glass is removed and the glass is removed, it's a good idea to seal the gap with packaging tape or duct tape to stop water and drafts from entering the home until a professional comes out and fix the window. This also serves as a barrier to prevent any intruders from making their way into your home. If the gap is particularly large, you might think about the security door with an integrated window, as it offers the best of both worlds.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash windows. Over time, they can develop a variety of issues that include sagging. A sagging window can cause problems with light, draughts, and even security. If you find that your uPVC window is beginning to sag it's important to act quickly to stop the issue from becoming worse.

To repair a window that is sagging, you can try to reposition the hinges. To do this, you'll need open the window to get to the frame. Then, remove both the hinges at the top and bottom using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. Close your window to check the fit after you have repositioned your hinges. If you are happy with the fit of your window, tighten the screws to keep them in place.

If you are unable to reposition the hinges, you could have to replace the seal. As time passes, rubber seals lose their elasticity and become dry which causes their tightness to decrease. If this happens, it's essential to replace the seal as soon as possible so that your uPVC windows remain watertight and safe from drafts.

UPVC handles can also become loose. The majority of the time this is due to screws that have come loose over time. However, it can occur because the handle mechanism has been worn out. It's fairly simple to fix a loose upvc Window Repair hand. The first step is to close the window and perform a test fit. The corner joints of the sash must be aligned with the casing joint. If it isn't then you can make use of a screwdriver to loosen the handle and return the mechanism to its original its original position.

3. Water Leaks

It is important to take action if you awake each day to find a smoky wall and floors that are wet. Leaks of water from windows can cause structural damage to your home and hinder your ability to control the temperature inside your home. Most of the time, uPVC window leaks are caused by a lack or damage to the sealant.

This is an easy fix that can be accomplished by anyone who is a DIYer with the skills. Depending on the severity of the problem the caulking used previously might need to be removed before a new layer of caulk can be put on. It is important to keep in mind that when it is about uPVC window repairs, you should not be tempted to 'over-caulk' as this will only make the area more difficult to clean and can reduce the efficiency of your energy.

Verify that the drainage holes have no debris in them and that the sill pan has been properly angled to drain away from the window. In more serious instances, Upvc Window Repair you might need to consider replacing the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives under humid conditions and can propagate quickly throughout the house.

It is also important to keep in mind that if the leakage originates from the glass in your double glazed windows, it's more likely to be a problem with the glass seal rather than the frame or sliding. Again this can easily be repaired by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and open with a breeze, it may be hinges at the fault. They can be easily replaced by any competent DIYer and can be done within a few minutes.

Like any mechanical component, hinges can be damaged over time. It's very simple to replace a hinge on a window but it's much easier if someone helps you hold the frame.

It is also important to verify that the uPVC hinges are opening and closed in the correct direction. You can check this by looking for the arrow on each hinge, this indicates the direction in which the window should be opened.

The problem can be caused either by opening the window incorrectly or a faulty installation at the factory. This can often be resolved by sending us a picture on our website. We will be happy to give you suggestions.

Regularly lubricating hinges is also essential. Applying an engineering lubricant that is light to the hinges is a great method to accomplish this. We recommend using a lubricant that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can help the window open and close more easily. It also helps prevent corrosion and reduce the risk of sticking. This should be done at least once a year. WD40 and other solvent based fluids are not recommended since they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different factors. The hinges may also become disaligned as a result of wear, which can cause a gap where the sash meets frame. If they are damaged beyond repair, it may be required to realign them. Second, the interlock can be misaligned. This happens on the hinge's side and may need to be cleaned. In certain instances it might be necessary to replace them.

The next common cause of draughts is the window seals. They are susceptible to being worn out or damaged over time, and will allow air to escape through the gaps. Replacement of these with high-quality weatherstripping is a good way to prevent draughts. Another alternative is to replace the window with glass that is low-emissivity, which will help regulate indoor temperatures and will reduce the risk of draughts.

Lastly, one of the most effective methods to reduce drafts is to use an draught excluder. These are usually fabric tubes that are filled with some kind of filler. They can be put on top of your windowsill. They will help block out cold air and keep your home warm and cosy!

The windows made of upvc can remain a great source of insulation and security for your home with regular maintenance and repairs. However, it is important to recognize that windows last for a certain period of time and there may come an point at which it is more efficient to replace them than fix them. If you are experiencing issues with your upvc window, it's best to consult a professional as soon as possible.