How to Replace a Kia Sportage Replacement Key

For a variety of Kia models keys, the key has a keyless entry system built-in. The key functions like remote controls, and can be exchanged by a Kia dealer.

Key fobs can fail to function due to a variety of reasons, including the battery being dead, worn-out buttons, signal interference or water damage. Here are some guidelines on how you can get your Kia Sportage replacement key to work again.

How do you replace a remote key or a smartkey?

Whether your Kia is equipped with an intelligent key, remote key, push to start key, or a standard non-transponder key made of metal, the battery in these keys will eventually require replacing. This is particularly the case if your car shows a message that states the remote or smart keys are in poor condition.

It's quite simple to do. In order to replace the battery of the key fob take out the mechanical key from the slit at the back of the key fob and break the cover. Inside the key fob, there will be the small screw that holds the battery in the correct position. Using a small screwdriver, remove the screw and remove the old battery. Install the new battery and then close the slit on the key fob.

When the key fob is equipped with new batteries Test it by pressing the locks and unlock buttons. If the doors lock and unlock according to your expectations, then you're set! You can now take advantage of Kia's hands-free lock/unlock function when your fingers start to get cold or you have to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a programing machine that is available only to the locksmith in the automotive or dealer. Other keys (non transponder keys made of metal) don't require programming. If you're looking to reprogramme your key, it is necessary to write down the key code's number on the tag for the key code.

how to get a new kia key; relevant resource site, do you replace the battery?

If your kia replacement key uk key fob isn't responding to pressing the lock or unlock button on the fob, it is a good indicator that the battery should be replaced. A battery that is not functioning properly could cause other issues such as the check engine light turning on or the engine not cranking. It is relatively easy to replace the key fob batteries with only two tools.

Before you begin before beginning the process, ensure that your vehicle is turned off and all doors are closed. Locate the small metal or plastic piece that is on the bottom of your key fob and move it until a metal key is released. This key can be inserted into the driver door handle to unlock your car.

To replace the battery in the key fob remove the cover that covers the rear. Use a plastic pry tool to remove the latch that holds the black negative cable. Take the old battery out, and then orient the replacement battery to ensure that its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid damaging or breaking the contacts on the metal.

After you have installed the new battery then turn the key fob on and off in the ignition until the door locks cycle. You can then test the Kia's key fob again to confirm that it is working correctly.

How do you replace a keyless keys

You can have the standard keyfob or Smart Key depending on the model of Kia Sportage. The difference between these is that the smart key has the small blade of a key tucked inside it, while the standard key fob does not. Both key fobs have batteries that eventually require replacement. It's an easy process that only takes about two minutes.

Before you get started it is important to ensure that you're on a level surface with good lighting and that the kia key replacement is off. Keep in mind that there are tiny pieces inside the fob which could be removed if not cautious.

The small release button is located on the lower backside. It will be either a circular silver button or a rectangular slot. When you press it mechanical key blade, it will come out and you will be able to open the key fob.

After the key fob has been removed, you can remove the battery that was in it. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. After you've finished you should be able to lock, unlock and start your vehicle with your key fob - even if the engine isn't running!

How do you replace the mechanical key

The Kia key fob is a great feature that lets us lock and unlock our vehicle with the push of the button. But, as with all devices, it can have problems from time to time. Luckily, there are steps that can be taken to resolve these issues and keep our key fobs in good condition in the long run.

A dead or drained battery is one of the most frequent problems. This can cause your fob to stop working or operate intermittently. If this is the case you should replace the battery an entirely new battery.

If this does not resolve the issue, use the flathead screwdriver that is standard to push the fob's casing made of plastic open. Be careful not to damage any internal components, or scratch the plastic. Once open, carefully remove the battery that was removed and replace it with a new one.

Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob and make sure it is working properly. Contact a dealer, or a locksmith to fix the issue if the fob is still not working. Make sure they make you an emergency key that functions for all trunk and door cylinders in order to avoid lockouts in the future.