Repairs to uPVC Windows

uPVC windows are a fantastic option for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to get rotten or rusty like timber and aluminum.

It is important to clean and oil UPVC windows and doors regularly. This will reduce unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and may even be fatal. It is essential to take the time to make sure that you're doing everything you can to keep your windows in good condition.

Single-pane windows are relatively simple to replace, and they generally fit into frames of the past easily. If you have double-paned windows that are held together by internal beading, it is harder to remove and replace the panes that were previously in use. In this case you'll need source some plastic spacers that help the new pane to fit perfectly into the frame of the window.

If you're planning attempt to remove the window panes yourself it is crucial to wear appropriate safety gear such as gloves that are thick and protective eyewear. You should also lay down a dropcloth before you begin working on the window panes so that any shards fall onto the fabric and not on the floor, where they could be trampled under.

Once the glass is removed and the glass is removed, it's a good idea to seal the gap with packaging tape or duct tape to block drafts and water from entering the home until a professional can come out and repair the window. This will also provide an obstacle to stop criminals from getting into your home. If the gap is large, you may be interested in a security door that has an integrated window, as it will provide the best of both worlds.

2. Sagging

uPVC is a durable and energy efficient alternative to timber sash windows. Over time, they can be affected by a variety of issues, including sagging. A sagging uPVC windows can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to shrink, it's crucial to act fast to prevent the problem from getting worse.

To fix a window that is sagging you can try repositioning the hinges. You'll first need to open the windows to access the frame. After that, using a screwdriver, you can remove the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. Once you've repositioned the hinges, close your window and verify the an appropriate fit. If you're happy with the fit, you can tighten the screws until they stay in place.

If you cannot reposition the hinges, you may have to replace the seal. Seals made of rubber can dry out and lose their elasticity with time, causing them to loose their elasticity. If this happens, it's crucial to replace the seal as soon as possible to ensure your uPVC windows are watertight and secure from draughts.

UPVC handles can also loosen up. Most often, this is caused by screws that have become loose over time. However, it can occur because the handle mechanism has worn out. Luckily, it's not difficult to repair the handle of a window that is loose yourself. First, you'll need to shut the window and perform an initial fitting. The joints at the corners of the sash should align with the joint on the casing. If it isn't then you can use the screwdriver to loosen up the handle. Then, you can turn the mechanism to position.

3. Water Leaks

If you're waking up to damp floors and mouldy walls each time it rains it is important that you take action. Windows that leak water do are not just a cause for destruction of your home's structure but also hamper your efforts to control the temperature inside your home. The most common reason for leaks in uPVC windows is that the sealant surrounding the frame is either damaged or missing.

It is a fairly easy fix and should be undertaken by any competent DIYer. Depending on the severity of the issue is, the old caulking might need to be removed. It is essential to keep in mind that when it is about uPVC window repairs, do avoid the temptation to "over-caulk and then make the area more difficult to clean and can decrease the efficiency of your energy usage.

Make sure that the drainage holes are free of debris inside them and that the sill pan has been properly angled to drain away from the window repair near me. In more serious cases you may need to think about replacing the window.

Moldy sills and rotten ones are other signs of water leakage. This is a fungus that thrives in damp conditions and is able to quickly spread throughout the home.

It is also important to keep in mind that if the leak originates from the glass of your double glazed windows it may be more likely to be an issue with the glass seal, rather than the frame or sliding. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges may be to blame when your uPVC window is difficult to open or it blows open with an ease. They can be easily replaced by any competent DIYer and are usually completed in a matter of minutes.

Like any mechanical part, hinges can wear out over time. Changing a window repairs hinge is essentially a very simple procedure, but it is simpler with someone else to help you hold the frame in place.

It is also worth checking that the uPVC hinges are opened and closed in the right direction. Look for the arrows that are on each hinge to determine which direction the window should be opened.

Window hinges that aren't working properly could be caused by improperly opening the window a certain way or by inadequate installation at the factory. Sending us photos through our website can often solve the issue. We are happy to give advice.

It is also important to ensure that the hinges are lubricated on a regular basis. This can be done by applying a light engineering oil to the hinges, we recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can make the window easier to open and close. It also helps prevent corrosion and decrease the chance of sticking. This must be done at a minimum every year. WD40 and other solvent-based lubricants are not recommended as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by different causes. Firstly the hinges, again due to wear and tear can become misaligned, this can cause gaps to develop where the sash meets the frame. They can be repaired by giving them thorough clean, however in the event that they are beyond repair it could be necessary to have them realigned or replaced. The second is the interlock, which is on the hinge side of the window, may also become misaligned, again it is feasible to give them a thorough clean, however in certain cases, it may be necessary to get them replaced.

The seals may wear out or get damaged over time, allowing air to escape. Installing high-quality weatherstripping will help to stop draughts. Another option is to replace the window with low-emissivity glass. which will help regulate indoor temperatures, and also reduce the risk of draughts.

One of the most effective ways to reduce the draughts in your home is to use an draught excluder. These are typically fabric tubes which are filled with a kind of filler. They can be positioned on top of your windowsill. They will keep your home warm by blocking cold air.

Your upvc windows can continue to provide excellent insulation and security for your home with regular maintenance and repairs. It is crucial to keep in mind that all windows will eventually get worn out and it may be more cost-effective to replace them rather than repair them. If you are experiencing issues with your Upvc windows, it's recommended to seek help from a professional as soon as possible.